Concentricity Tolerance: What It Controls and How to Inspect It
Need Custom Components?
Looking for a direct China factory for plastic or hardware parts?
Your Direct China Manufacturer
In-house production for custom plastic and hardware parts.
Where Concentricity Problems Usually Begin
A concentricity problem often becomes visible after parts have already been made. A molded sleeve fits its mating pin, yet its outer surface looks off-center. A machined collar meets its diameter limits, yet it wobbles when assembled on a shaft. The drawing may say that two diameters must be “concentric,” but the supplier and buyer may have used different methods to judge that requirement.

At that point, the disagreement is not necessarily about workmanship. It may be about what the drawing actually controls. Does the design need an even wall, a bore in the right location, or an outer surface that runs true during rotation? Those are related concerns, but they are not the same inspection task.
The most reliable way to avoid a late-stage dispute is to work backward from the assembly risk. Define the functional datum, choose a geometric control that addresses the risk, and agree on a measurement method before tooling or production is approved. This matters for both injection-molded components and metal hardware: a tight tolerance is useful only when it is relevant, achievable, and verifiable.
What Concentricity Tolerance Actually Means
In ordinary production language, concentricity means that two circular or cylindrical features share a center or axis. An engineer might use it to describe an outer diameter centered around a bore. That informal meaning is useful in conversation, but it is not precise enough for acceptance decisions.
In legacy ASME geometric dimensioning and tolerancing, concentricity is a specific control of the median points of opposed surface elements relative to a datum axis. For a cylindrical feature, those median points must fall within a cylindrical tolerance zone centered on the datum axis. The requirement is not simply that two fitted circles appear to have the same center on one cross-section.
If a drawing specifies a cylindrical concentricity tolerance of diameter 0.10 mm, the allowable zone is a cylinder 0.10 mm in diameter around the established datum axis. It does not mean that a measured center may move 0.10 mm in any radial direction. Just as importantly, the result depends on how the datum is established and how the median points are evaluated.
Check the drawing standard and edition before interpreting the symbol. Concentricity was removed from ASME Y14.5-2018, although it still appears on drawings produced under earlier editions. Other drawing systems may use related terms differently. An older requirement should not be silently replaced with another control: the designer and manufacturer should agree on what function the requirement was intended to protect.
Choose the Control That Matches the Assembly Risk

Many calls for “concentricity” are really requests for a different, more directly useful control. A locating bore may need to be positioned relative to mounting features. An outside diameter may need to rotate without excessive variation. A thin wall may need to remain sufficiently uniform. Identifying the concern before assigning a symbol makes drawings easier to quote, manufacture, and inspect.
| Design concern | Control to consider | Practical inspection question |
|---|---|---|
| A bore or cylindrical feature must be located relative to specified datums | Position, where appropriate for the feature and drawing standard | Is the feature’s derived axis within the specified position tolerance zone? |
| A surface must run true as the part rotates about a datum axis | Circular runout or total runout, depending on the extent of surface control needed | How much does the measured surface vary during rotation at the specified locations? |
| Median points of opposed surface elements must be centered on a datum axis under a legacy drawing requirement | Concentricity, interpreted under the applicable drawing standard | Can the median points and datum axis be evaluated by an agreed method? |
| Material around a bore must not become too thin | A combination of feature location, size, form, and minimum wall requirements as needed | Does the inspection plan directly protect the minimum acceptable wall? |
Position is often a clearer choice when the concern is where a hole or other feature of size sits relative to the rest of the part. Depending on the applicable standard and design, its feature control frame can also specify material-condition requirements that reflect assembly clearance. It should not, however, be substituted automatically for a legacy concentricity requirement without checking the intended function.
Runout addresses a different question. Circular runout evaluates variation at individual circular cross-sections as the part rotates about the datum axis. Total runout evaluates variation across the controlled surface during rotation and can constrain more of its overall form. A dial indicator may make a runout check relatively straightforward, but the reading is influenced by the surface being measured, not just by a theoretical center offset.
None of these controls alone guarantees uniform wall thickness in every situation. Size variation, out-of-roundness, draft, and local distortion can change the wall even when a feature is reasonably well located. If minimum wall is critical to strength or molding feasibility, state and verify that requirement directly rather than assuming the word “concentric” covers it.
Establish the Datum Before Discussing Measurement
Concentricity only has meaning relative to a datum axis. The drawing must make clear which feature establishes that axis and how the part is oriented during inspection. For a component assembled on a pin, the mating bore may be the logical datum feature. For another design, the functional axis may come from an outside cylindrical surface. The correct choice follows the way the part is located in use, not whichever surface is easiest to hold.
A datum feature is a physical surface with real variation. Its derived datum axis is established through the applicable datum rules and the chosen inspection setup. If two teams support a part differently or fit axes to different portions of a surface, they can obtain different results from the same component. An agreed inspection plan should therefore identify the datum feature, any other datum references, the contact or sampling region, and how the part will be restrained.
This is especially important for molded parts. A nominally cylindrical hole may have draft, a parting-line effect, or distortion after cooling. Measuring only at the opening and treating that center as the full bore axis can miss variation deeper in the feature. Metal parts present their own risks: burrs, surface damage, or a short datum length can affect setup stability. These observations do not make the parts unacceptable; they show why datum establishment must be planned rather than improvised at final inspection.
For molded components, inspection timing may matter as well. A part measured while still warm or held in a way that distorts it may not represent its agreed inspection condition. For hardware parts, cleaning and deburring before measurement may be necessary to prevent a small raised edge from driving the reading. The buyer and supplier should settle these conditions before comparing inspection reports.
Plan Concentricity Measurement and Inspection Around the Requirement
There is no single measurement method suitable for every use of the term. A legacy concentricity GD&T callout requires evaluation consistent with its median-point definition and the specified datum. Appropriate coordinate measurement may be used when the instrument, access, sampling strategy, and evaluation method can support that task. A few points on each diameter or a fitted-circle comparison do not automatically establish compliance.
Likewise, a dial indicator reading taken while rotating a part is generally a runout observation, not a direct verification of legacy ASME concentricity. It may be exactly the right production check if the functional concern is wobble. The distinction matters when a buyer requests a concentricity report but expects the supplier to record total indicated variation: without clarification, both parties can believe they agreed while applying different acceptance criteria.
Before approving a concentricity inspection plan, resolve these questions:
What is the functional concern? Identify whether failure would come from poor fit, insufficient wall, interference, visible eccentricity, or variation during rotation.
During sample development, inspection should feed back into manufacturing decisions. If the feature does not meet the agreed requirement, look beyond a simple “center offset.” For a molded part, examine whether the mold geometry, material behavior, or cooling-related distortion is influencing the feature relationship. For a processed metal component, consider the sequence in which datum and controlled surfaces are made and held. Corrective action should address the cause seen in measurements, not merely increase final sorting.
Apply the Requirement Without Creating Avoidable Cost
A tighter geometric tolerance can change how a part is made, inspected, and quoted. It may require more attention to the mold or process sequence, a more controlled setup, additional measurement time, or more iteration during sample approval. If the function does not require that precision, an unnecessarily restrictive callout can raise cost and delay production without improving the assembly.
The opposite risk is an underspecified drawing. “Keep the two diameters concentric” leaves open the datum, tolerance limit, measurement method, and acceptance condition. A supplier may reasonably quote a routine dimensional check while the buyer expects a formal GD&T evaluation. That gap can emerge only after samples arrive, when changes are more expensive.
JATERSON approaches these questions from its manufacturing scope: injection molding, hardware production, sample development, and production coordination. For a plastic component or standard hardware part, the useful preproduction discussion is not whether a concentricity value looks demanding on paper. It is whether the datum can be established on the real part, the selected control protects the assembly, and both teams can verify it consistently.
When reviewing a drawing or quotation, provide the mating-part relationship and identify the feature that locates the component in use. If a critical wall or rotating surface is involved, state that explicitly. Ask the manufacturer to flag a tolerance that depends on an unclear datum, conflicts with draft or expected part form, or lacks a practical inspection route. Resolve those issues before sample approval, then keep the agreed drawing revision and inspection method aligned through production changes.
Use concentricity tolerance only when its defined control is the one the design needs. For many parts, position, runout, or a direct wall requirement communicates the risk more clearly. The best specification is not the strictest symbol; it is the one that lets engineering, production, and quality teams reach the same defensible decision on the same part.
Recent Comments (0) 0
Leave a Reply